Oil centrifuge for edible oil and fat clarification in Vietnam

Source:

Author:

Hui Bo

Release time:

2026.11.18


Walk through any edible oil refinery in Vietnam, whether it sits near Ho Chi Minh City, in the Mekong Delta, or in the port zone around Hai Phong, and the same machine shows up at several points in the line: a tall, closed, high-speed vessel with a motor on the side and a tangle of small-bore piping on top. That is the oil centrifuge. It removes gums after degumming, soapstock after neutralisation, wash water after washing, and, in some lines, wax crystals or fine haze. In animal fat and fish oil plants it also separates the melted fat from water and protein.

This article explains where an oil centrifuge machine, in the sense of a disc-type centrifugal oil separator (a disk stack centrifuge, sometimes labelled a bowl centrifuge on drawings, and centrifugation de l'huile in French-language papers), belongs in a vegetable oil and animal fat line, what it does at each step, how it fails, and what to look at when a plant in Vietnam has to push high volumes through it day after day. It covers soybean, rice bran, peanut and corn oil, plus pangasius fat and fish oil. It does not cover the internal mechanics of the disc stack, which are treated in the guide to centrifugal oil-water separators, nor coconut oil or palm oil, which have their own articles.

oil centrifuge edible

Where an oil centrifuge works in an edible oil refining line

Refining is a sequence of chemical conditioning steps, each followed by a physical separation. The chemistry turns an unwanted component (phospholipids, free fatty acids, waxes) into something that no longer dissolves in the oil: a gum, a soap, a crystal. The separation then has to take that new phase out before the next step. Gravity settling does this too, but slowly. A disc centrifuge does it in seconds, continuously, in a closed vessel.

Not every step uses a centrifuge. Bleaching earth is removed by filters, and deodorisation is a vacuum steam-stripping process. The centrifuge belongs on the wet steps, where two liquids or a liquid and a fine solid have to be split.

Refining stepWhat the centrifuge removesTypical feed conditionMain thing to watch
Water or acid degummingHydrated phospholipid gums (heavy phase)Crude oil heated, mixed with a small dose of water or dilute acid, then held for hydrationGum stickiness; oil carried away in the gum
Alkali neutralisationSoapstock (soap, water, residual gums)Degummed oil mixed with caustic solution, hotNeutral oil lost into the soapstock; soap carry-over
Water washingWash water carrying residual soapNeutralised oil mixed with hot soft waterResidual soap in the oil; emulsion
Dewaxing (some oils)Wax crystals, where a separator is used rather than a filterOil cooled slowly and held to grow crystalsCrystal damage in pumps and mixers
Fat or fish oil clarificationWater and fine protein or tissue from melted fatFat cooked, pressed or decanted, still warmFatty acid rise and oxidation from heat and time

Each step needs different settings even if the bowls look identical: in neutralisation the heavy phase is viscous soapstock, in washing it is nearly clean water, and in degumming the gum behaves like a gel that plasters the disc stack if discharge is late.

Physical refining changes the count. Plants that refine low-phosphorus oils by physical (steam) refining skip alkali neutralisation and its soapstock separator. They still need a centrifuge after degumming, and often another one on the polishing side. Count the wet steps in the actual flow sheet, not in a generic diagram.

Degumming: what it achieves and where the centrifuge sits

Crude vegetable oil carries phospholipids. Some of them are hydratable: add a little hot water, hold for a while, and they swell into a heavy gum that can be separated. Others, mostly calcium and magnesium salts of phosphatidic acid, are non-hydratable and stay in the oil unless an acid such as phosphoric or citric acid breaks the metal bond first. Soybean oil has plenty of both types.

The sequence in a typical acid degumming line is: heat the oil to a temperature in the range of roughly 60–90 °C depending on the route, dose acid and mix intensely, add a small amount of water to hydrate the gums, give the mixture a residence period measured in tens of minutes so the gum particles grow, and only then feed the separator. The centrifuge does not create the gum; it only collects what the residence step has built. If the hydration is poor, the machine will show it immediately as a hazy light phase and a gum phase that is mostly oil.

What the separator does here

The degumming separator is a liquid-liquid machine. The oil is the light phase, the hydrated gum with water is the heavy phase, and the gum stream leaves continuously through the heavy outlet or, when it is stiff, is partly collected in the bowl and ejected during discharge. Gum is also the main reason this machine needs a larger hydraulic discharge system than a polishing separator.

The gum phase always takes some oil with it; the aim is to keep this low through good hydration and a steady feed. A rise in phosphorus in the leaving oil usually means shorter hydration time, a crude oil change, or a feed rate beyond what the machine can handle. Gums harden when they cool, so heat-trace the gum line and flush with warm water at shutdown.

Choosing a degumming route

Water degumming is the simplest route and removes only the hydratable gums; it suits oils that will be neutralised afterwards, and it also yields lecithin as a by-product when the gum is dried. Acid degumming adds an acid to convert the non-hydratable fraction first, and it is the usual choice for soybean oil and for any oil destined for physical refining, where phosphorus must come down far before the bleaching step. Enzymatic degumming, using phospholipase in a controlled-temperature reaction tank, is also used in some refineries. In every route the separator sees the same thing, a gum that has had time to grow, so residence time and mixing intensity set the result more than the machine does.

Oils differ in what they need. Soybean carries the most phospholipid. Rice bran, corn and sunflower carry less but bring wax along with the gum, and a wax-bearing gum is stickier and harder to keep moving.

Neutralisation and soapstock removal with a disc centrifuge

Alkali refining converts free fatty acids into sodium soaps by mixing the degummed oil with caustic soda solution. The soap, together with water, residual gum and colour bodies, forms soapstock, a heavy and viscous emulsion. The centrifuge pulls it out of the oil within seconds of the reaction, which matters because contact time lets caustic attack the neutral oil as well.

Where the soap goes

Soapstock is the heavy, viscous phase, and the oil leaves clean only if the soap stays in it. Soap content, water content and temperature all change how readily the two phases part, so a refinery that blends crude oils from different shipments, or mixes locally pressed oil with imported soybean oil, will see the soapstock behave differently from one tank to the next. Settings for the phase split itself belong to the three-phase decanter article; here the refining question is how much neutral oil rides out with the soap.

Handling the soapstock afterwards

Soapstock is not waste to be thrown out. Many plants collect it in a heated tank, keep it pumpable, and sell or process it. A common route is acidulation: sulphuric acid splits the soap back into free fatty acids, producing acid oil that is separated from the acidic water layer and used as a feedstock elsewhere. This makes the oil content of the soapstock a matter of yield, and it explains why the plant watches neutral oil loss closely. Keep the line warm, because cold soapstock sets to a paste that no pump will move.

Neutral oil loss to soapstock

A free fatty acid that becomes soap is expected to be lost, but neutral oil is not. Excess caustic saponifies triglyceride, poor mixing leaves pockets of high alkalinity, gums from weak degumming stabilise the emulsion, and low temperature thickens the soapstock and traps oil. A separator cannot fix any of these; it only shows them. When neutral oil in the soapstock climbs with the machine unchanged, check the mixer, caustic dosing and degumming before touching the centrifuge.

Troubleshooting a neutralisation separator

Symptom at the plantLikely causeFirst check
Soapy, hazy oil leaving the light-phase outletToo much soap for the throughput; weak hydration in the degumming step upstreamReduce feed rate and see if the haze clears; check the previous step before touching the machine
Heavy phase thick and heavily loaded with oilExcess caustic; poor degumming; temperature too lowTitrate or check the caustic dose; check feed temperature at the machine inlet, not at the heater
Heavy-phase flow drops, then bowl overflowsGum or soap hardening in the outlet line; hydraulic discharge not firingWarm flush the line; check discharge water supply and operating water pressure
Vibration climbing over daysUneven deposit of gum or solids on the bowl wall or disc stackPlan a manual clean of the bowl and discs; review discharge interval
Emulsion in the light-phase sight glass after a crude oil changeHigher phospholipid or free fatty acid load than the setting assumedAdjust feed rate and caustic dose together; do not change one alone

Water washing, polishing and dewaxing

After neutralisation, the oil still holds a small amount of soap. A water wash removes it: hot soft water is mixed into the oil, forms fine droplets that pick up the soap, and the washing separator takes the droplets out. The quantity of wash water is a modest fraction of the oil flow, commonly somewhere between five and fifteen percent by weight depending on the number of wash stages and the plant's own limits. Too little water leaves soap in the oil and shortens the life of the bleaching earth in the next step. Too much water makes a more stable emulsion and a wetter oil to dry.

In many refineries the neutralisation and washing separators are identical machines with different ring sizes. A washing machine carries very little heavy phase, so its heavy outlet is small and easily plugged by scale; a fine strainer upstream protects it.

Dewaxing

Sunflower, rice bran and corn oils contain natural waxes that cloud the oil when it cools. Dewaxing cools the oil slowly so wax crystals grow, then removes them. Many plants use filters; some use centrifuges, where crystals are grown gently enough to settle readily. Fast-formed crystals are small and fragile, and pumps shear them further.

Edible oil and fat processing in Vietnam: plant conditions and raw materials

Vietnam's edible oil and fat industry is organised around a few distinct raw material streams, and each creates a different working condition for an oil centrifuge. This is a qualitative description from the process side, not a statistical survey.

Port-side refineries and imported crude oil

Many large refineries in Vietnam sit near ports, because crude oil arrives by sea. These plants run long campaigns with few crude grades, which suits centrifuges. The usual trouble is blending: a tank topped up from three cargoes has a different free fatty acid and phospholipid profile at the bottom than at the top, and the separator sees it as a soap load that wanders over a shift.

Rice bran and corn in the south

The Mekong Delta produces large amounts of rice, and rice milling produces bran. Rice bran contains lipase that begins to break triglyceride into free fatty acids as soon as the bran is milled, in a warm, humid climate within hours. That makes crude rice bran oil high in free fatty acids, wax and gums, and it produces heavy soapstock with a stubborn emulsion. For a Vietnamese refinery processing rice bran oil, the neutralisation separator is under more pressure than in a soybean plant, and the dewaxing step is usually needed for a clear table oil. Corn oil from germ pressing is cleaner, but it carries wax and some gum and shares the dewaxing challenge.

Pangasius and fish processing

Mekong Delta provinces also run aquaculture and fish processing, with pangasius fillet plants producing fat and offal. These by-products spoil quickly in the heat, and free fatty acid in the oil rises with every hour of delay.

Humid heat in Vietnamese oil plants

Ambient temperatures above thirty degrees and high humidity are normal across most of the country. For an oil centrifuge this shows up as condensation inside converter and PLC cabinets in the monsoon season, bearing-oil temperature alarms in the afternoon, and cooling water warmer than the design condition. Specify sealed, ventilated cabinets and check the cooling water supply under afternoon load.

Regional boundary. Plants in Thailand running fat and oil lines share many of these conditions and are covered by the same process logic. For the bigger picture of oily process water and used lubricants, see the article on Malaysian disc-type oil-water separation.

Animal fat and fish oil clarification in Vietnam

Animal fat and fish oil refining begins with rendering. Raw material (fat trim, skin, fish heads and offal) is cooked at moderate temperature, usually near eighty or ninety degrees, to break the cells and release the fat. The result is a mixture of oil, water (often called stick water) and solid protein particles. A decanter first removes the bulk solids, and a disc separator then splits the oil from the stick water and removes the fine solids that remain. A three-phase decanter can do the first stage and part of the second; a polishing disc machine finishes the oil.

The key difference from vegetable oil is that the oil has already been heated and is sensitive. Every extra hour at temperature increases free fatty acid and oxidation products. A line should be designed so that the time between cooking and the final oil tank is short, and the separator should receive a feed that is already stable in flow. The three-phase decanter's role on oil, water and solids is explained in the palm oil three-phase decanter article; the same oil, water and solids split applies to fat and fish oil, with different densities.

A typical sequence: cook and press the raw by-product; remove bulk solids in a three-phase LWS decanter; polish the oil in a disc separator; recover oil from the stick water in a second machine; then store the oil with minimal air contact, because oxidation continues after separation.

Dry and wet rendering, and what the separator receives

Fat reaches the oil line by two common routes. In dry rendering the raw material is cooked in a jacketed vessel until the water has boiled off, and the fat is drained and pressed from the cracklings. In wet rendering, steam or hot water is added and the melted fat floats off a watery mixture. Wet rendering gives a feed with more water and fine protein, which is what a three-phase decanter and then a disc polisher are suited to. Dry rendering gives a drier, hotter fat with fine crackling dust, which asks for a strainer or decanter first. Fish oil usually comes from cooked, pressed fish, with the press liquor split into oil and stick water, so the polishing step sees a thin, watery feed with fine solids.

Fat that will not behave

Some animal fats set a few degrees below the working point, and a feed line that cools by ten degrees between cooker and separator can turn a free-flowing stream into a paste. Insulate and trace the pipework. A Vietnamese fat plant that stops its separator for an hour at night can return to a bowl full of set fat, so a warm-water flush sequence on the control panel is worth having.

Corn, rice bran, peanut and soybean oil: can one line serve all?

Plants in Vietnam often run more than one oil. The question is whether the same centrifuge line can handle corn oil, rice bran oil, peanut oil and soybean oil, and the honest answer is that it can, if the settings are changed by oil and if the worst-case oil is accounted for in the specification.

OilWhat makes it harder for the separatorWhat to plan for
SoybeanHigh phospholipid content, significant non-hydratable fractionAcid conditioning and a larger gum discharge capacity
Rice branHigh free fatty acid, wax and gum; heavy soapstock; strong emulsion tendencyNeutralisation separator with ample margin; a dewaxing step; generous hydraulic discharge
PeanutModerate gum; solids and fine particles from pressing; odour carry-overPrefiltration or a decanter ahead of the disc stage when feed is dirty
Corn (germ oil)Wax and moderate gumDewaxing step and attention to crystallisation

A corn oil centrifuge is not a different machine from a soybean one; the difference sits in the feed, since corn germ oil arrives with fine germ particles and wax and is often settled or filtered first. When switching oils, write the changeover into the procedure: flush, check the settings sheet, reset the discharge interval, and test the first output before accepting it into a tank.

Choosing oil centrifuge equipment for high-volume oil processing in a factory

The question that comes up most often in refineries expanding capacity is which oil centrifuge equipment is best suited for high-volume oil clarification. One note on wording first: a centrifuge is not a filter. People say "oil filtration" for any clean-up step, but a disc centrifuge separates by density and works on emulsions and fine solids that would blind a filter cloth within minutes.

One large machine or several smaller ones

A refinery needing a high hourly flow can install one large machine per step or two smaller ones in parallel. The pair keeps the line running at half rate when one is stopped for cleaning, which matters for a continuous line. Decide from the downtime pattern, not from a catalogue throughput number.

Discharge type

A disc separator with hydraulic partial discharge opens the bowl briefly, ejects a measured amount of solids, and closes while the machine keeps running. A nozzle-discharge machine runs a steady solids stream and suits higher solids content. The more gum or soap the feed carries, the more the choice moves to automatic discharge with adjustable intervals. The three discharge types are compared in the disc separator article.

Feed conditions that decide throughput

  • Temperature. Oil viscosity falls with temperature, so a warmer feed settles faster. The limit is oil quality, not the machine.
  • Back-pressure. A closed machine with a pressurised light-phase outlet keeps the bowl full and prevents foaming. A drop in back-pressure is often the first sign of a blocked outlet line.
  • Feed stability. Surges in flow upset the separation. A buffer tank and a metering pump upstream do more for performance than any adjustment inside the machine.
  • Solids content. Particle loads above the design range lead to frequent discharges and loss of oil in the discharged slurry. A decanter or strainer in front takes this load off the disc stage.

Industry reference values

Typical Industry Reference Values for a Disc Oil Centrifuge in Edible Oil Refining

Feed temperature for chemical refining stepsRoughly 60–90 °C, set by the process
Separation force at the bowl wallSeveral thousand g (commonly 5,000–12,000 g for disc machines)
Solids content tolerated by oil-water-solid machinesLow, generally below about 2%
Wash water ratio in a water washAbout 5–15% by weight of oil flow
Contact materials for food-grade serviceStainless steel with food-grade elastomers
Control of dischargeTimed or load-based, adjustable by PLC

These are guideline figures for engineers, not design limits. Real values depend on the oil, the crude oil quality and the supplier's own design data.

Food-grade hygiene, CIP and automation for oil centrifuges

An edible oil centrifuge is a food-contact machine, even when it sits in a refinery that looks more like a chemical plant. In Vietnamese export-oriented plants, buyers' audits cover the machine's materials, cleaning method and records.

Materials and design

Product-contact surfaces should be stainless steel with smooth finish and no crevices where oil can sit. Elastomer seals must be of food-grade quality, and the supplier should be able to give declarations of compliance for the markets that the plant exports to. Dead legs in the piping around the machine are as much a hygiene issue as anything inside it.

Clean-in-place

Cleaning an oil centrifuge is more than a water rinse: hot water, a cleaning solution at an agreed concentration, then a rinse, with the bowl rotating and discharges operated to flush the solids space. The sequence must wet every product surface: inlet, bowl, disc stack, outlet paths and discharge mechanism. Plants running different oils on one machine need a validated routine, because residual oil can carry flavour or allergen traces into the next batch.

Automation

A PLC that controls discharge timing, interlocks the feed with bowl speed, and records feed temperature, back-pressure and vibration gives the evidence that audits ask for and warns of trouble before oil is lost. Frequency converter start-up also eases the stress on the belt drive during acceleration.

Huibo disc separators and three-phase decanters for oil and fat lines in Vietnam

For the refining steps described above, Huibo's disc separator range is the main answer, with a three-phase decanter for the heavier feeds.

  • DBX-2 and DBX-3 with piston-type automatic slag discharge. The published uses include animal and vegetable oils with low solids, and refining steps such as degumming, desoaping, dehydration and dewaxing. In a Vietnamese refinery, that covers the gum separation after degumming and the soapstock split after neutralisation.
  • DBPX with continuous nozzle discharge. For feeds with more solids, about 1–25%, the nozzle discharge removes them without stopping, which suits the solids-laden streams in the upstream part of a line.
  • Bowl inner diameter from 330 to 785 mm. One series therefore spans a small refinery in the Mekong Delta and a high-volume port refinery.
  • Stainless steel contact parts and PLC discharge control. The contact parts meet food hygiene needs, and the PLC sets the discharge volume and interval, which keeps oil loss steady between operators and shifts.

For feeds with more solids, such as rendered fat or fish oil, the LWS three-phase decanter handles oil-water-solid separation, including fish meal and fish oil production, and a disc separator can follow it for polishing.

To start, send the oil type, feed temperature, solids content and flow, and the technical team will recommend the model.

Frequently asked questions

How does a centrifuge remove soapstock after neutralisation?
After caustic is mixed into degummed oil, free fatty acids become soap, which collects with water and residual gums as a heavy, viscous phase. The mixture enters a disc separator at a temperature near 60–90 °C. Inside the bowl, the lighter oil leaves through its own outlet while the soapstock is thrown outwards and leaves separately. Two losses matter: soap carried into the oil, which burdens the wash step, and neutral oil carried out with the soapstock, which is lost yield. In a Vietnamese refinery running rice bran oil, a heavier soap load makes discharge setting and the following wash more important than for soybean oil.
What does degumming achieve, and where does the centrifuge sit?
Degumming removes phospholipids from crude vegetable oil, because left in place they cause dark colour, foaming, and higher refining losses in later steps. Hot water hydrates the hydratable fraction into a heavy gum; for the non-hydratable fraction, an acid such as phosphoric or citric acid is dosed first. After a residence period of tens of minutes, the mixture goes to a disc separator that splits the oil from the gum. The centrifuge sits directly after the hydration tank and before neutralisation, or before bleaching in physical refining. Good hydration is what makes the separation work: the machine collects gum that already formed, and cannot create it.
What are the steps for fish oil and animal fat clarification?
Raw fat or fish by-product is cooked at moderate temperature to release the fat, then pressed or fed to a decanter to remove bulk solids. A three-phase decanter can separate oil, stick water and solids in one pass. The oil then goes to a disc separator for polishing, where fine solids and remaining water are removed, and the stick water goes to a second machine for oil recovery. In Vietnam, where pangasius by-products and fish residue spoil quickly in the heat, the time from cooking to polished oil should be kept short, because free fatty acid and oxidation rise with each hour at temperature. Insulated lines and warm flush sequences keep fat from setting in the pipework.
Which oil centrifuge setup suits high-volume factory service?
The choice rests on solids load, discharge type and downtime pattern. For clean or lightly loaded oil, a disc separator with hydraulic partial discharge and PLC control suits continuous refining. Feeds with a larger solids content, such as rendered fat, call for a three-phase decanter ahead of the disc machine, or a nozzle-discharge disc type. Decide whether one large unit per step or two in parallel better fits the plant: parallel machines keep the line running at reduced rate during cleaning. Stable feed temperature and flow, with a buffer tank upstream, matter as much as machine size. A centrifuge separates by density; it is not a filter, and it is not replaced by one.
What should be checked in a disc centrifuge for food facilities: hygiene, CIP and materials?
Start with product-contact surfaces: stainless steel, smooth finish, no crevices. Elastomer seals should be food grade, with compliance documents for the export markets involved. Confirm that clean-in-place covers every wetted surface (inlet, bowl, disc stack, outlets, discharge mechanism) and that the sequence can be run with the bowl rotating. Look for PLC control that records feed temperature, discharge events and vibration, which audit teams in Vietnamese export plants often ask for. A centripetal pump on the outlet keeps the line closed and limits air pick-up, which helps oxidation-sensitive oils. Finally, confirm how the machine is drained and dried after cleaning.
Can corn or rice bran oil use the same line as soybean oil?
Yes, provided the settings are changed by oil and the line is sized for the hardest one. Rice bran oil carries more free fatty acid, wax and gum, and forms heavier, more emulsified soapstock, so it loads the neutralisation separator and usually needs a dewaxing step. Corn germ oil needs dewaxing attention and often a prefilter for germ fines. Soybean oil needs strong degumming capacity. For a Vietnamese refinery, write the changeover into the operating procedure: flush, check the settings sheet, reset the discharge interval, and test the first output before accepting it into storage. Clean the line between oils if allergen separation is required.