Sludge dewatering centrifuge for wastewater treatment plants in Indonesia

Source:

Author:

Hui Bo

Release time:

2026.11.18


A sludge centrifuge turns a thin, smelly slurry from a clarifier or digester into a stackable cake and a liquid that can go back to the head of the plant. In Indonesia that job is getting heavier every year, as municipal sewage schemes around the big cities add capacity and the industrial estates in West Java and East Java push more textile, food and paper effluent through their treatment lines. Whoever runs the sludge end of those plants meets the same question sooner or later: what should sit between the thickener and the truck?

This article is written from the treatment-plant side of the fence. It covers which sludges reach a sludge dewatering centrifuge, why polymer conditioning decides most of the result, what controls cake dryness, how a centrifuge compares with a belt filter press, and what to put into a spesifikasi when asking for a kapasitas figure. The general anatomy of the machine (bowl, scroll, gearbox) is already covered in the decanter centrifuge guide for Indonesia and is not repeated here.

Horizontal decanter centrifuge

Sludge types that reach a sludge centrifuge in Indonesia

"Sludge" is not one material. A centrifugal machine for sludge that behaves well on digested municipal solids can struggle on waste activated sludge from a food plant, and neither resembles the grey grit-laden mud coming out of a water intake. For an Indonesian plant engineer the first job is to name which of these streams the plant really has. Before any machine is discussed, the plant should name which of these streams it actually has, because the settling behaviour, the polymer demand and the abrasion load are all different.

Sludge typeTypical source in IndonesiaBehaviour in the bowlPoints to watch
Waste activated sludge (WAS)Municipal sewage plants, extended-aeration package plants, food and beverage effluent systemsLight, hairy floc; high water-binding; settles slowly and sheds fines under shearHighest polymer demand; cake stays soft; sensitive to feed-solids swings
Primary sludgePrimary clarifiers at municipal works, pre-treatment at industrial sitesDenser, more fibrous; dewaters more readily than WASRags and fibres can wrap around the scroll; grit wear
Digested sludgePlants with anaerobic digestersFine, well-stabilised; responds well to cationic polymerHigh ammonia in centrate; temperature of feed affects polymer
Industrial biological sludgeTextile dyeing and finishing, pulp and paper, food processingVaries with the process; often oily, coloured or high in fibreGrease blinds floc; dye and surfactants shift polymer choice
Chemical (physico-chemical) sludgeCoagulation and flocculation of industrial wastewater, metal or lime precipitatesDense, quick-settling, but often abrasive and alkalineWear on scroll hard-facing; lime scaling in the bowl
Mineral and dredged sludgeWater-intake clarifiers, quarry and mining drainage, river and harbour dredgingHeavy, high-density solids with a wide particle rangeAbrasion first, polymer second; sand in the feed pump

Centrifugal sludge thickener or dewatering centrifuge: two different jobs

In centrifuge water treatment the same family of machine serves both thickening and dewatering, and the confusion loses plants a lot of commissioning time. A centrifugal sludge thickener takes a dilute feed, typically waste activated sludge at around one percent solids or a little more, and lifts it to a pumpable thick sludge of several percent. Cake does not form in the sense of a spadeable solid; the output is still a liquid-like paste that goes to a digester or a storage tank. Polymer demand is modest, sometimes none at all, and the machine is run at a gentle differential speed with a deep pond.

A dewatering centrifuge starts from a feed that is already at a few percent solids and aims at a cake that holds its shape on a conveyor. Here the polymer is not optional. The pond is shallower, the bowl runs at the high end of its speed range, and the scroll torque is watched closely because the cake is now dense enough to jam the conveying section.

Check before specifying: Write down the feed solids concentration at the machine inlet, not the figure on the process flow diagram. Sludge that arrives at 0.8 percent instead of 3 percent changes the hydraulic load by a factor of nearly four for the same weight of solids, and the machine that looked generous on paper runs out of volume capacity before it runs out of solids capacity.

The sludge line: conditioning, feed, dewatering and cake handling

A centrifuge works as one link in a chain, and most complaints that arrive labelled "centrifuge problem" are caused by a neighbour of the machine. The sequence on a normal line looks like this.

Buffer tank, feed pump and polymer dosing

Sludge should reach the machine from a mixed holding tank, not straight from a clarifier underflow, so that the polymer dose set in the morning is still right in the afternoon. A grinder or screen ahead of a steady, non-pulsing feed pump removes rags and plastic before they reach the scroll.

Powder or emulsion polymer is made up to a dilute solution, aged, and dosed by a metering pump that follows the feed flow. Dilution water for the final dosing point is usually a separate line, so that the polymer is mixed into the sludge close to the machine inlet. Mixing too early lets floc break in the pipe; mixing too late leaves the polymer unreacted when it enters the bowl.

The centrifuge

Conditioned sludge enters the feed tube and is thrown to the bowl wall. Solids compact against the wall and are scrolled up the conical beach; clarified liquid leaves over the weirs at the other end. The LW series horizontal decanter in the product section below has a fully closed casing and a dual-motor, dual-converter drive, which in a sludge room means the bowl speed and the differential can be adjusted independently while the feed continues.

Centrate return

The liquid leaving the machine, the centrate, goes back to the head of the biological process. It is not clean water. It carries fine solids that escaped capture and, in the case of digested sludge, a hot, ammonia-rich stream that the aeration basin will have to treat. This return load is the reason that solids capture matters as much as cake dryness; the point is covered in its own section below.

Polymer conditioning: why it decides whether the centrifuge works

Raw biological sludge will not dewater at any reasonable rate in a centrifuge, or in anything else. Its particles are small, negatively charged and surrounded by bound water. Cationic polymer neutralises the charge and bridges the particles into larger flocs, which both settle faster in the bowl and release a good part of the water they were holding. The machine then does its work on a conditioned material whose behaviour is far more favourable.

Three variables dominate: the type of polymer, the dose, and the mixing energy. Type means charge density and molecular weight; a high-molecular-weight, medium-to-high charge cationic is a common starting point for municipal biological sludge, but industrial sludges with oil, dye or surfactant content can behave very differently and need jar tests with a handful of candidates. Dose is usually expressed as kilograms of active polymer per tonne of dry solids, and the working range for a given sludge is narrow: too little leaves the centrate cloudy, too much leaves slimy, over-conditioned sludge that slips through the bowl with a wet cake and, in the worst cases, a sticky coating on the scroll.

Signs that polymer is off target

  • Under-dosed: centrate looks milky or grey, solids capture drops, cake is wet and mushy, and the scroll torque is low because little is being compacted.
  • Over-dosed: centrate is clear and sometimes slightly stringy, but the cake is slick and wet; polymer residue builds up on screens and in pipework; torque may climb while dryness falls.
  • Well-tuned: centrate clear with a few visible fine flecks, cake that breaks rather than smears, torque steady within its normal band.

The practical routine at most plants is a step test. The operator moves the polymer flow in small increments, waits several residence times for the machine to settle, and watches centrate clarity and torque. The optimum sits just on the clear side of the point where the centrate turns from cloudy to clear; going beyond that point only adds chemical. Re-testing is needed when the sludge changes, which in a tropical plant means after a heavy rain event, after a change in the incoming industrial mix, or when the temperature of the sludge tank rises through the afternoon.

What drives cake dryness in a sludge dewatering centrifuge

Cake dryness is the number people ask for first and the one that is most often misunderstood. A single figure in a catalogue means very little because the same machine can deliver cake at quite different dryness on different sludges. The factors that move it are fairly well understood.

  • Sludge character. Digested and primary sludge hold less bound water than waste activated sludge, and they come out drier. The age of the sludge in the biological process matters too: very young, lightly stabilised sludge is stickier.
  • Polymer conditioning. Poor floc formation leaves free water in the cake; well-formed floc gives a firm structure.
  • Bowl speed. Higher g-force presses harder on the cake in the cylindrical and conical sections. The gain flattens above a certain level, and the extra speed adds wear and vibration.
  • Pond depth. Raising the pond improves centrate quality but sends the cake through a shorter dry beach, so it leaves wetter. Lowering the pond does the reverse.
  • Differential speed. A lower differential gives solids more time on the beach and a drier cake, but raises the solids load in the bowl and can overload the scroll. A higher differential clears solids faster and gives a wetter cake.
  • Feed rate. More feed means less residence time for the same bowl; cake gets wetter and the centrate dirtier.
  • Temperature. Warm sludge is less viscous and dewaters a little more readily, though it also encourages biological activity in storage.

Typical Industry Reference Values for Sludge Decanter Service (indicative ranges)

Dewatering bowl accelerationRoughly 1,500–4,000 g
Feed solids, waste activated sludge (after thickening)About 2–5 % dry solids
Cake dryness, waste activated sludgeOften in the mid-teens to low twenties % dry solids
Cake dryness, digested or primary-rich sludgeOften low to high twenties % dry solids
Solids capture with good conditioningTypically above 90 %
Cationic polymer demandCommonly several kg active per tonne dry solids; varies widely by sludge

These are broad reference figures from general practice. Actual results depend on the sludge, the polymer and the way the machine is set, and any commitment to a particular cake dryness should come out of a test on the plant's own sludge.

Centrate return: the load that comes back to the plant

A centrifugal sludge dewatering machine does not remove material from the plant; it moves it from the sludge stream to the cake and to the centrate. Of the two, the centrate is the stream that can destabilise biology if nobody watches it. It carries residual suspended solids that will settle in the clarifier and loop round again, dissolved nitrogen and phosphorus released from the sludge, and in warm-digester cases a stream hot enough to affect aeration oxygen transfer.

Belt filter press vs centrifuge for sludge dewatering

The comparison of a belt filter press with a centrifuge comes up in nearly every sludge project, and the honest answer is that each wins in a different set of conditions. The table keeps to technical characteristics.

AspectDecanter centrifugeBelt filter press
Operating principleCentrifugal sedimentation in a closed rotating bowlGravity drainage, then pressure and shear between moving belts
Footprint for a given throughputCompact; one machine in a small roomLarger floor area, with belt wash and drainage equipment
Enclosure and odourFully enclosed; air handling limited to a small extract pointOpen belt area; usually needs a hood or a room with extraction
Cake dryness on biological sludgeGenerally somewhat higher, especially on difficult sludgeLower on average; sensitive to belt condition and wash
Polymer demandOften a little higher at the same feedOften lower at the same feed
Response to feed changesFast; settings can be changed while runningSlower; belt speed and pressure must be re-balanced
Wear pointsScroll flights, bowl, bearingsBelts, rollers, bearings, wash nozzles
Wash waterLittle or none in operationSubstantial belt wash water, which goes back to the plant
Operator attentionLower once settings are fixed; checks on vibration and torqueHigher; belt tracking, tension, cleanliness
Fine, light biological sludgeWorks well with proper polymerWorks, but cake is often wetter
Very abrasive mineral sludgeNeeds hard-faced scroll flightsBelts wear quickly on sharp grit

For Indonesia the decision rests on three things. Where odour and enclosure matter in an Indonesian urban setting, because the plant sits near housing or has a tight ventilation arrangement, the closed centrifuge has a clear advantage. Where the plant has operators who know belts well, runs low-solids feed and wants minimal polymer use, a belt press remains a sound machine. And where the sludge varies a lot from day to day, the centrifuge's ability to adjust speeds on the fly is hard to match.

There is also the question of what is being dewatered. Free-draining granular solids, such as washed mineral or crystalline material, go to filtering machines such as the pusher centrifuge range; the sedimentation-versus-filtration split is explained in the centrifugal separator guide.

Sludge dewatering conditions in Indonesian treatment plants

Indonesia is not one climate or one type of plant. Greater Jakarta, Bekasi and Karawang carry some of the densest industrial and residential loads in the country; around Surabaya and Sidoarjo the textile, food and paper effluents dominate the industrial side; Medan, Batam and parts of Kalimantan have their own mix of agro-processing and port industry. Municipal sewerage coverage is still being extended in many cities, and that expansion is what brings new sludge handling units onto the drawing board. Many existing septic and communal systems also produce faecal sludge that arrives at treatment depots in trucks, with a very different character from sewer sludge.

A few site conditions repeat across Indonesian plants and are worth designing for.

  • Humidity and heat. Sludge ferments quickly in a warm holding tank, which changes its dewatering behaviour between morning and afternoon. Tank residence time before the centrifuge should be kept short, and aeration or mixing maintained in the buffer tank.
  • Heavy rain. During the wet season, combined or leaky sewers and open industrial drains dilute the incoming flow. The sludge becomes lighter and the polymer demand changes. A plant that holds a stored dose from the dry season will find the centrate cloudy for a week.
  • Cake disposal routes. Landfill access, composting capacity and cement-kiln co-processing differ by region. The moisture and handling requirements of each route should be known when the dewatering target is set.

Palm oil mill sludge has oil and fibre issues of its own; the oil recovery side is dealt with in the three-phase decanter guide for palm oil mills. Enquiries about a sludge centrifuge in Malaysia raise the same polymer and feed-solids questions, and the same method of reading the sludge before the machine applies there.

Reading spesifikasi and kapasitas of a sludge centrifuge for Indonesian plants: hydraulic vs solids load

Buyers and consultants in Indonesia often ask for a spesifikasi sludge centrifuge and a kapasitas sludge centrifuge as if each were a single line in a catalogue. A better question is what the machine is being asked to move, because a decanter has two separate capacity limits and either one can be the one that stops the plant.

Indonesian consultants writing a spesifikasi for a new sewage scheme or an estate effluent plant can use the same checklist; the figures differ from site to site but the structure does not.

Hydraulic load

This is the volume of feed per hour. It is limited by the settling time available in the bowl. If the feed rate is too high, solids do not have time to reach the wall and the centrate fouls. At a fixed bowl size, thinner feed means a lower solids throughput because volume is the constraint.

Solids load

This is the weight of dry solids per hour. It is limited by how fast the scroll can convey the settled solids without overloading its torque. With a thick feed or a high cake output, the machine reaches its torque limit while there is still hydraulic room.

Plants that state only a flow figure, for example cubic metres per hour of feed, miss half the picture. A machine rated for a certain flow on 1 percent sludge will not carry that flow on 4 percent sludge, because the solids load is then four times higher.

Data to supplyWhy it matters
Sludge type and origin (WAS, primary, digested, industrial, mineral)Sets polymer demand, cake dryness expectation and wear allowance
Feed solids concentration, with minimum, average and maximumConverts hydraulic load into solids load
Design flow and the operating hours per dayDetermines whether one machine or a working and standby pair is needed
Volatile solids fraction and sludge ageIndicates how bound the water is
Grit, sand and fibre contentDrives material of flights and the need for screening
Chemistry: pH, chloride, sulphide, oil and greaseDetermines alloy choice and the risk of polymer inhibition
Target cake dryness and the disposal routeDefines the dewatering goal and the cake conveying design
Maximum acceptable centrate solidsDefines the capture requirement
Available polymer type and dosing systemAvoids a mismatch between the machine and the chemistry
Site: ambient temperature, power supply, room size, enclosure and odour limitsFixes drive design, ventilation and layout

When the same data are given to several suppliers the replies can then be compared on equal terms. A catalogue number with no stated feed concentration should be treated as incomplete. Where the sludge is new or poorly known, a short on-site trial at the Indonesian plant, run with a borrowed or supplier-provided test machine on the plant's own sludge, resolves more questions than weeks of correspondence.

Troubleshooting a sludge decanter: symptoms, causes and first actions

SymptomLikely causeFirst action
Cake is wet and slumps on the conveyorPolymer under- or over-dosed; pond too deep; differential too high; feed solids too lowCheck centrate appearance; run a polymer step test; lower the pond; reduce differential in small steps
Centrate is cloudy or greyUnder-dosed polymer; feed rate too high; worn flights; feed solids spikeIncrease polymer a little; reduce feed; inspect flights at the next stop
Scroll torque climbs and trips the driveSolids load above limit; cake too dense; sludge with sand or hair; differential too lowReduce feed; raise differential; check the screening upstream
Vibration alarmUneven solids build-up in the bowl; worn flights; bearing wear; feed tube blockedFlush the bowl with water; check feed tube; stop if vibration stays high
Machine blocks after a shutdownSolids dried and hardened in the bowl; no flush before stoppingAlways flush with water before the stop; keep a standing shutdown routine
Rags wrapped round the scroll or feed tubeNo screening or grinder in the feed lineFit a grinder or screen ahead of the pump
Rapid wear on the beach sectionGrit or mineral solids; unprotected flightsRemove grit upstream; specify hard-faced flights for the service

One pattern comes up often in wet-season operation: the centrate has been clear for weeks, then turns cloudy within a shift, and the first instinct is to blame the machine. In most cases the sludge has become lighter after heavy rain and the dose needs raising a little. Check the feed concentration and the dose before opening anything.

Shutdown routine: Stop the feed first, flush with clean water until the centrate and cake run clear, then slow the bowl. Solids left to dry in a warm bowl are the most common cause of vibration trips on the next start-up.

Odour control and enclosed operation

In Indonesian cities, sludge smell is a plant-boundary issue before it is an engineering one. Dewatering rooms are often built close to residential areas or to other process buildings, and in a humid climate odour compounds travel farther on still, warm evenings. A decanter has an advantage here because the rotating parts and the discharge sit inside a closed casing; the main emission points are the cake outlet chute, the centrate outlet and the feed tank vent.

The LW series horizontal decanter in the product section below is described with a fully closed casing, which supports this kind of installation. A sensible layout includes a small extraction point at the cake chute connected to a scrubber or biofilter, a cover on the cake conveyor, and a sealed hopper or a covered truck bay. Septic sludge that has sat in a warm tank for days is more offensive than fresh sludge, and quick processing is the simplest odour measure available.

Huibo LW and LWS decanter centrifuges for sludge dewatering in Indonesia

Xiangtan Huibo makes horizontal decanters for exactly this job, and the product page names sludge dewatering in municipal and industrial wastewater treatment among the uses of its LW series horizontal spiral discharge sedimentation centrifuge. The features below are the ones that matter on an Indonesian sludge line.

  • Continuous feed and continuous discharge. The scroll moves settled sludge to the cone end without stopping, so a plant in Greater Jakarta or Surabaya that receives sludge every day can run the machine through the shift instead of batching.
  • Adjustable differential speed, cone angle and pond depth. Wet-season sludge is thinner and dry-season sludge is thicker; these settings are how the operator follows the change in polymer demand and cake dryness described earlier.
  • Double motor with two frequency converters. Bowl speed and scroll speed are set independently, which is what allows the differential to be tuned while the machine runs.
  • Fully closed casing and automatic control. The closed casing keeps odour and aerosol inside the machine, which counts for plants close to housing, and the automatic control suits sites where one operator watches several units.

Where the sludge also carries a second liquid, such as oily industrial wastewater, the LWS three-phase version adds a second liquid outlet and an adjustable centripetal pump, so oil and water leave separately from the solids.

To start, send the sludge type, feed solids, flow and target cake dryness, and the technical team will review them and recommend the LW or LWS configuration.

Frequently asked questions

Belt filter press vs centrifuge for sludge dewatering: which is better?
Neither wins everywhere. A decanter centrifuge is enclosed, compact, quick to adjust and usually delivers a drier cake on fine biological sludge, but it often needs somewhat more polymer and has high-speed wear parts. A belt filter press is gentler, can use less polymer on suitable sludge and is simple to understand, but it has an open belt area that releases odour, needs wash water and is sensitive to belt condition and feed changes. For a plant near housing, or with sludge that changes from day to day, the centrifuge tends to fit. For a plant with a steady feed, low solids and experienced belt operators, the press is a sound choice. Side-by-side tests on the plant's own sludge settle the question best.
What drives cake dryness in a sludge centrifuge?
Sludge character comes first: digested and primary sludge dewater better than waste activated sludge. Polymer conditioning comes next, because poorly formed floc leaves free water in the cake. Within the machine, bowl speed, pond depth, differential speed and feed rate all move the result; a deeper pond and a higher differential give wetter cake, while higher speed and a lower differential give drier cake at the risk of higher torque. Cake dryness must always be read with solids capture, since a very dry cake can be bought by losing fines to the centrate.
How should the spesifikasi and kapasitas of a sludge centrifuge be read, hydraulic versus solids load?
A decanter has two limits. The hydraulic limit is the feed volume per hour that still leaves enough settling time; the solids limit is the dry weight per hour the scroll can convey within its torque range. A flow figure alone is therefore incomplete: the same machine handles far less volume of a 4 percent sludge than of a 1 percent sludge. For an Indonesian plant the specification should state sludge type, minimum, average and maximum feed solids, design flow, operating hours, target cake dryness, maximum centrate solids, grit and chemistry, so that every supplier answers the same question.
What are the signs that the polymer dose needs optimising?
Cloudy or grey centrate, falling solids capture and soft, mushy cake point to too little polymer. A very clear centrate with slimy, sticky cake, polymer residue on screens and a wetter result than before points to too much. A well-tuned dose gives a clear centrate with a few fine flecks, a cake that breaks instead of smearing, and torque inside its normal band. The usual method is a step test: change the polymer flow slightly, wait several residence times, then check centrate and torque. Repeat after rain events, changes in industrial inflow or a swing in feed solids.
How does centrate return affect the rest of the plant?
The centrate goes back to the head of the biological process and carries residual fine solids, dissolved nitrogen and phosphorus released from the sludge, and in digester cases a warm, ammonia-rich stream. If solids capture is poor, the fines circulate: they settle in the clarifier, return to the thickener and come back to the centrifuge. Polymer carried over can foul diffusers and membranes. Plants usually return centrate at a steady controlled rate rather than in pulses, and they track centrate suspended solids as a routine measurement alongside cake dryness.
Does a sludge centrifuge help with odour, and does it need to be enclosed?
An enclosed decanter keeps the rotating sludge inside a sealed casing, so the main release points are the cake outlet, the centrate outlet and the feed tank vent. That is a real advantage over open belt equipment, especially in warm, humid Indonesian conditions where odour travels far on still evenings. Extraction at the cake chute, a covered conveyor, a sealed hopper and a scrubber or biofilter complete the arrangement. Short storage times and an aerated buffer tank reduce the amount of odour generated before the sludge ever reaches the machine.